Cornelius UC 700 Series Manual de usuario

IMPORTANT:TO THE INSTALLER.It is the responsibility ofthe Installer to ensure thatthe water supply to thedispensing equipment isprovided with protecti

7 630460127INSTALLATIONPRE–INSTALLATIONFreight Damage ClaimThe delivery of your equipment (Frieght Company, Distributor, or dealer) is responsible for

8630460127INSTALLATION1. Keep unit in the upright position, remove carton and pallet from the Icemaker and inspect for damage. Ifany damage is found,

9 630460127INITIAL START UP, CHECKS AND ADJUSTMENT INSTRUCTIONSNOTE: Do not start Icemaker before completing installation steps on pages 7 and 9.Turn

10630460127THIS PAGE LEFT BLANK INTENTIONALLY

11630460127GUIDE TO SERVICEWARNING: Disconnect electrical power to the Icemaker to prevent personal injury beforeattempting any internal maintenance.

12630460127Semi–AnnuallySemi-Annually in addition to all previously established service procedures perform the following:1. Check for water leaks in t

136304601273. The transparent bowl not only provides a visible check of water level, but also is a good guide to the inter-nal conditions which exist

14630460127EXPANSION VALVEYou will find a thermostatic expansion valve on icemakers, which is used to control the amount of refrigerantflowing through

15630460127FIGURE 5. EXPANSION VALVEFIGURE 6. ADJUSTMENT SCREWTHERMOSTATICEXPANSION VALVESIGHTGLASSCONDENSER MODULATING VALVE REMOVAL1. Disconnect pow

16630460127GEARMOTORThe gearmotor is equipped with a start relay and a manual reset overload.When current is applied, the relay energizes and complete

i630460127TABLE OF CONTENTSPageSAFETY INFORMATION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17630460127START RELAY1. Check between “2” and “4” on relay (with relay unplugged). If there is continuity replace the relay, as therelay contacts sho

18630460127AUGER AND EXTRUDING HEAD REMOVAL1. Disconnect unit from power supply.2. Remove storage container cover and put aside.3. Turn off water supp

196304601273. Remove Dispense Tray Cover.4. Use an open end wrench on auger nut connected to bearing and turn counterclockwise to remove assembly.5. R

20630460127FIGURE 12. GEAR MOTOR OVERLOADSAFETY CONTROLSYour icemaker unit has several safety and control devices incorporated into its design.WARNING

21630460127GUIDE TO GOOD ICECUSTOMERCOMMENTSCHECK ICEMAKER LOCATION CONDITIONSFIRSTCHECK ICE MAKERS Use gauges for checkingsuction and headpressures.

22630460127FIGURE 13. WIRING DIAGRAM

23630460127TROUBLESHOOTING CHART – ICEMAKER NOT OPERATINGNO POWERCheck electrical wiring in con-trol box for loose connec-tions.Check for failed servi

24630460127TROUBLESHOOTINGIMPORTANT: Only qualified personnel should service internal components or electrical wiring.TROUBLESHOOTING COMPRESSORSTrou

63046012725PARTS LIST

26630460127FIGURE 14. PANEL COMPONENTS123567891011121314151617181911120ItemNo. Part No. Name1 07578 Thread Cutting Screw, Phil Truss Hd,No. 8-32 By 3/

ii630460127TABLE OF CONTENTS (cont’d)PageUPPER NUT AND BEARING ASSEMBLY 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TO REPLACE

63046012727ItemNo. Part No. NameIce Chute Components1 38220 Machine Screw, 1/4-202 630000741 Elbow, Ice Chute3 630250106 Tube, Ice Transfer4 630900564

28630460127ItemNo. Part No. NameCompressor Components1 164154001 Washer, Flat, >375 I.D.2 165596002 Grommet3 168770002 Machine Screw, Hex Hd, 5/16-

63046012729ItemNo. Part No. NameEvaporator Components1 630200737 Bracket2 630900558 Adaptor, Front End Ass’y3 630900559 Gasket, Front End Ass’y4 63090

30630460127IMI CORNELIUSCERTIFICATE OF WARRANTYTWO YEAR LIMITED ICE EQUIPMENT WARRANTYIMI Cornelius warranty to the original commercial purchaser/user

31630460127THIS PAGE LEFT BLANK INTENTIONALLY

One Cornelius PlaceAnoka, Minnesota 55303-6234Telephone (800) 238-3600Facsimile (763) 422-3246Corporate Headquarters:IMI CORNELIUS INC.

1 6630460127SAFETY INFORMATIONRecognize Safety InformationThis is the safety-alert symbol. When you see thissymbol on our machine or in this manual, b

2630460127THIS PAGE LEFT BLANK INTENTIONALLY

3630460127GENERAL DESCRIPTIONTO THE USER OF THIS MANUALThis manual covers the installation and assembly of the Air–Cooled or Water–Cooled Model UC700

4630460127Table 1. Design Data (cont’d)Water Supply–Water inlet fitting is 1/4–inch SAE flare located at the top front of the Unit. The Unit is design

5630460127FIGURE 1. CLEARANCE REQUIREMENTS

6630460127THIS PAGE LEFT BLANK INTENTIONALLY